02 Helitehnika

Cluster mounting set 2 x ATEO6 speaker White

The CPA12 is a professional single channel 100V power amplifier with a power of 120 Watt, especially designed for most common 100V PA systems and perfect to be used in combination with the CPR12 pre-amplifier. It is designed as a no-nonsense amplifier with only the necessary controls and connections. This creates great simplicity in use and installation. There are several power output taps available for use in 100V, 70V and even 4 Ohm Low impedance installations and they are fitted with an advanced multipurpose protection circuit. The protection circuit detects DC malfunction, short circuit, overheating, overload and limits the signal when necessary. Another present feature is the 24 V DC connection for powering the amplifier with emergency power when the main power is shut down. At the back of the amplifier, there are trim potentiometers to set the input level, a high pass filter switch and a ground lift switch provided. The input connection is made with balanced XLR connectors and there is a signal output for linking with other amplifiers. The steel 19″ housing has a height of 2 HE.

ceiling flying system for 1x FX 3.15 – black Black

The BASO cabinets are universally usable passive bass cabinets. Their bass reflex design is engineered to be as compact as possible while giving the maximum performance in terms of sound quality and pressure. Their enclosures are crafted out of sturdy high-quality plywood while their elegant design enables them to be placed in any environment. The BASO10 is loaded with a 10” high-performance woofer with an RMS power rating of 225 Watt and maximum power of 450 Watt. The strength of this loudspeaker originates from a four layer wounded 1.5” voice coil in combination with an over-sized ferrite type magnet which provides an unusual high force factor. In combination with the low-loss suspension, this results in a linear behaviour with high efficiency and extremely wide frequency range These carefully selected high-grade materials in collaboration with accurate acoustical craftsmanship results in a deep and true to nature reproduction of bass. The highly-efficient design results in a sensitivity of 96 dB with capability of continuous sound pressure production up to 120 dB. The frequency response ranges from 54 Hz up to 1.2 kHz while going down to 38 Hz at -10 dB. Besides these acoustical aspects, a lot of attention has been paid to all other aspects making it as versatile as possible. The enclosure is compact designed without any sacrifice to robustness due to the 15 mm high-quality plywood material finished with structured coating. Connections are made using two SpeakON compatible connectors located in a recessed connector dish, allowing link-through to other cabinets. This also allows close placement to any wall or corner.

Ceiling speaker with fire dome 100V White version – RAL9010

Outdoor sound projector 100V

Public Address Amplifier 40W @70/100V

The M2DIS is an optional display unit with touchscreen which can be installed internally in the front panel of the M2 Multi-Media Digital Audio Mixer. This unit consists of a 7” TFT display panel with a resolution of 800 x 480 px that is fitted with a resistive touch-screen panel. It is controlled by a powerful 32 bit processor which communicates directly with the M2’s DSP processor. This unit allows the user to operate the control functions of the matrix systems without any external equipment. So it is now possible to set up zone selection or input mixing without any external devices. This can be useful when the system is installed in a technical room where no external control devices are within reach.

Connection cable with 5-pin awx5 connector 0.7 meter, white colour

The DSP40 is a professional DAB/DAB+ & FM tuner which provides access to a wide variation of radio stations while guaranteeing a high-quality audio reproduction. Station selection can be done manually or automatically, while up to 10 preferred channels can be internally stored and recalled. The front panel of the system accommodates a 2.8” TFT display in combination with a push rotary function dial and 4 tactile pushbuttons. The controls and indicators on the front panel of the unit are guaranteeing an intuitive and user friendly operation, allowing hassle free operation and configuration to even unexperienced users. Information such as radio station information carried by RDS / Radiotext and signal reception strength are indicated. The signal output level is user configurable while dynamic range compression (DRC) is supported, improving the intelligibility for low volumes in applications with high levels of background noise. Other functions such as mono/stereo (FM) switching always guarantee the best possible audio reception. The antenna input is implemented by an F-type connector allowing connection of the included antenna cable or any other external antenna using 75 O coaxial cabling. The balanced stereo line output is connected through two 3-pin terminal block connections. The RS-232 communication port allows system integration with any home or industrial automation system, while an optional 2.4 GHz remote control allows handheld control while hidden out of sight.

Please note: An outdoor antenna is necessary for DAB/DAB+ reception. For DAB/DAB+ reception we suggest the RGA12 outdoor DAB/DAB+ antenna.

Discover more about our modular audio players

Outdoor design column speaker 12 x 2″ Outdoor white version

Connection cable with 5-pin awx5 connector 0.7 meter, black colour

Speaker built-in box for concrete casting with mineral fibreboard

Professional 2.1 soundbar White

The CPB series are heavy duty splash waterproof speaker bags especially designed for the protection and handling of the AUDAC PX and RX speakers in all possible situations. The design ensures that it is possible to reach the connections, place the speaker on a stand and carry the speaker using the speaker handles even when the cover bag is attached. When not used, all these openings can be covered with a stitched flap from the same material. The front of the bag can be opened with a zipper to use the speaker without removing the bag. During transportation and storage, the front can be closed to avoid any damage to the speaker. The bags are made out of extra strong, water repelling polyester with heavy duty stitching and are finished with small rubber feet. The inside has a special soft coated protection to avoid structural damages.

Quad-channel power amplifier 4 x 480W 100V

Connection cable with 5-pin awx5 connector 2.5 meter, white colour

The CPB series are heavy duty splash waterproof speaker bags especially designed for the protection and handling of the AUDAC PX and RX speakers in all possible situations. The design ensures that it is possible to reach the connections, place the speaker on a stand and carry the speaker using the speaker handles even when the cover bag is attached. When not used, all these openings can be covered with a stitched flap from the same material. The front of the bag can be opened with a zipper to use the speaker without removing the bag. During transportation and storage, the front can be closed to avoid any damage to the speaker. The bags are made out of extra strong, water repelling polyester with heavy duty stitching and are finished with small rubber feet. The inside has a special soft coated protection to avoid structural damages.

The CS series loudspeakers are high-quality in-ceiling loudspeakers, delivering exceptional sound quality and value for a wide variation of applications, ranging from paging and announcements to background music systems in a wide range of business applications, including hotels, restaurants and pubs, corporate offices, retail stores, etc. The CS85 in-ceiling loudspeaker features a 8” driver with a coaxially mounted 1” tweeter, having a continuous power handling of 40 Watt and a maximum power handling of 80 Watt. The 2-way construction makes the CS85 the perfect match for a wide variation highly demanding of applications, guaranteeing a high-quality reproduction of music and speech with true and deep performance in the low frequency range. This guarantees a true Hi-Fi experience. The moisture proof treatment on the speakers’ cone and aluminum front grill protects it for installation in humid or outdoor environments. A multi-tapping line transformer fitted with Fast-con™ allows fast and smooth connections to 100 Volt public address or low impedance systems. The mounting of the loudspeaker into the ceiling is achieved with a Quick-fix mechanism, offering a great installers convenience and lifetime stability. The construction of the speakers’ housing is made out of high-quality ABS, while the front is covered by a solid powder-coated aluminum grille. It comes available in different colours, while custom painting is possible for a total blending into any environment.

Dual-channel power amplifier 2 x 240W 100V

The CPB series are heavy duty splash waterproof speaker bags especially designed for the protection and handling of the AUDAC PX and RX speakers in all possible situations. The design ensures that it is possible to reach the connections, place the speaker on a stand and carry the speaker using the speaker handles even when the cover bag is attached. When not used, all these openings can be covered with a stitched flap from the same material. The front of the bag can be opened with a zipper to use the speaker without removing the bag. During transportation and storage, the front can be closed to avoid any damage to the speaker. The bags are made out of extra strong, water repelling polyester with heavy duty stitching and are finished with small rubber feet. The inside has a special soft coated protection to avoid structural damages.

QuickFit™ 2-way 8″ ceiling speaker with TwistFix™ grill White version, 8Ω & 24 Watt @ 100V

The DMP40 is a professional DAB/DAB+ & FM tuner featuring SourceCon™ modular technology. This unique technology guarantees true plug & play implementation to any compatible device. When inserted to a supporting slot, the module is instantly installed, discovered and ready for operation without requiring any additional internal wiring or complex configuration. The DMP40 provides access to a wide variation of radio stations while guaranteeing a high-quality audio reproduction. Station selection can be done manually or automatically, while up to 10 preferred channels can be internally stored and recalled. Radio station information carried by RDS / Radiotext can be retrieved, while other functions such as mono/stereo switching (FM) always guarantee the best possible audio clarity. The signal output level is user-configurable, while dynamic range compression (DRC) is supported, improving the intelligibility for low volumes in applications with high levels of background noise. Signal reception strength can be retrieved from the module and indicated on the graphical interface of the controlling device. The antenna input is implemented by an F-type connector on its panel, allowing connection of the included antenna cable or any other external antenna using 75 O coaxial cabling. The balanced stereo line output is connected through two 3-pin terminal block connections.

Please note: An outdoor antenna is necessary for DAB/DAB+ reception. For DAB/DAB+ reception we suggest the RGA12 outdoor DAB/DAB+ antenna.

Discover more about our modular audio players

Compact 10″ bass reflex cabinet White version

Quad-channel power amplifier 4 x 240W 100V