• Toode lisati ostukorvi:

    Audac TR2050 Eraldustrafo 2x RCA-M -2x RCA-F

    Kohatäide
    0 out of 5

    Audac TR2050 Eraldustrafo 2x RCA-M -2x RCA-F

    The TR2050 is a basic ground loop isolator designed to electrically isolate audio devices from each other. Hum in audio systems is usually caused by ground loops in the system. A common mode current will flow in a ground loop created by an electrical system that has grounds on different voltage potentials. This results in a 50 Hz hum in the audio signal. The most common method to solve these problems is an audio isolation transformer such as the TR2050 which always need to be in reach for every audio technician. When ground loop problems are encountered, these can be solved in a jiffy, by using the TR2050.

    8,92 
  • Toode lisati ostukorvi:

    Audac VC3102/W Helitugevuse regulaator releega 100V/100W 45x45mm, valge

    Kohatäide
    0 out of 5

    Audac VC3102/W Helitugevuse regulaator releega 100V/100W 45x45mm, valge

    The VC3102 is a 100 Volt volume controller capable of handling a power up to 100 Watt. The volume is adjustable with a rotatable dial in 11 steps of 3 dB. It is equipped with a relay and separate input for the reception of 24V priority signals. This means that when a priority signal occurs, the volume will be automatically switched to maximum level. This can be very useful for emergency and evacuation messages. Due to it’s slim and good looking design, these volume controls will blend into all kinds of different environments or interiors. The construction is made of sturdy ABS and therefore suitable for big projects in industrial buildings as well as standard home interiors. The dimensions are 80 mm x 80 mm, and a built-in depth of 46 mm is required. The connections are made at the back with screw terminal blocks.

    35,75 
  • Toode lisati ostukorvi:

    Audac TR266 Eraldustrafo 1:1/600Ω

    Kohatäide
    0 out of 5

    Audac TR266 Eraldustrafo 1:1/600Ω

    The AUDAC TR266 is a super shielded true isolation audio transformer which is especially designed to be used in highly polluted EMI environments. Hum in audio systems is usually caused by ground loops in the system. A common mode current will flow in a ground loop created by an electrical system that has grounds on different voltage potentials. This results in a 50 Hz hum in the audio signal.The most common method to solve these problems is an audio transformer. The AUDAC TR266 audio isolation transformer with an in- and output impedance of 600 Ohm and a turns ratio of 1 : 1 has a very wide bandwidth and very low distortion which ensures a non distorted bass response and non attenuated high frequencies. Thanks to its MU-metal shielding, it can guarantee the best performance in even the most EMI polluted environments. MU-Metal is a soft ferromagnetic material with a very high magnetic permeability. It consists of an alloy of Nickel, Iron, Copper and Molybdenum. MU-Metal has a magnetic shielding effectiveness going from 100x up to 1000x higher than steel of equivalent thickness. It is especially good in 50/60hz type applications where all other shieldings fail. The TR266 super shielded transformer can be used for applications where the shielding of standard transformers becomes inadequate. A typical example of such an application is the broadcast system in railway stations.

    41,67 
  • Toode lisati ostukorvi:

    Audac DSC70/B Kõlarikaabel trossiga 7m, must

    DSC-B-Small-2
    DSC-B-Small-2
    0 out of 5

    Audac DSC70/B Kõlarikaabel trossiga 7m, must

    Connection cable with dual steel core, snap hook & open ends – 7 meter. For use with the ALTI series speakers (not suited for ALTIxM series). This connection cable with two integrated steel cores is designed for suspension with an additional drop safety. Fixation is made through two snap-hooks on one end and a dual Gripple™ fixation on the other end.

    33,83 
  • Toode lisati ostukorvi:

    Audac WMI16/B Pesapaneel 45x45mm XLR-F - rj45 konverter, must

    Kohatäide
    0 out of 5

    Audac WMI16/B Pesapaneel 45x45mm XLR-F – rj45 konverter, must

    The WMI16 is a Wall Microphone Input unit which can be used in combination with AUDAC MTX series Multi-Zone audio matrix systems, the RM523 & AMP523 web-based input control units and the APG20 receiver gateway. It provides the possibility for transferring an audio signal from a Microphone level audio source over a large distance by using standard CAT5e UTP (or better) cable.

    The connection should be made using an RJ45 connector on the back side of the unit. The depth of the RJ45 connector will not allow the WMI16 to be installed in surface mount boxes. A jumper on the rear side of the panel allows you to enable the 12V phantom power for powering condenser microphones and the audio transfer is done in a differential way with increased voltage levels, making the transferred signal insensitive for interference and noise generated by external devices. This allows bridging distances up to 500 meter between the input unit and the receiver end.

    The WMI16 is the 45 x 45 mm version of the WMI units, which can be used in combination with standard AUDAC, Niko, Legrand or other 45 x 45 mm installation materials. Available in Black (/B) and White (/W).

    75,00 
  • Toode lisati ostukorvi:

    Audac MWX65/W Juht- ja sisendpaneel MTX maatriksile, valge

    MWX65-W-Small
    MWX65-W-Small
    0 out of 5

    Audac MWX65/W Juht- ja sisendpaneel MTX maatriksile, valge

    The MWX65 is an all-in-one wall panel controller to be used in combination with the AUDAC MTX series multi-zone audio matrix systems. It can control the input signal and volume for one zone and also contains an additional line and microphone level input which can be patched to the zone it is connected to. Both input selection and volume control as well as two band tone control can be controlled using the versatile rotatable push-dial while the integrated 2.5” graphical display ensures a user friendly experience. An XLR connector is provided as additional microphone input while the line input is performed using RCA connectors. The signals applied to these inputs can be used as one additional local input. This enables you to connect any CD or MP3 player as local music source or connect a microphone for speeches or other announcements. The input mixing can be done by using both push-lock potentiometers. The microphone input has the possibility to provide 12V phantom power which can be turned on and off by software configuration. The wiring between the matrix and the wall panel should be performed by using standard UTP CAT5 cabling which transfers both the control and audio signals to the matrix while providing the power supply for the wall panel.

    158,92 
  • Toode lisati ostukorvi:

    Audac WP225/B Sisendpaneel universaalne Bluetooth-ga, must

    Kohatäide
    0 out of 5

    Audac WP225/B Sisendpaneel universaalne Bluetooth-ga, must

    The WP225 is a remote wall mixer that can be used in combination with various AUDAC hardware (ARES5A, MTX series, AMP523 and more). It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, … ) or balanced microphone to the level corresponding to the differential signal input making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling. On the front side of the wall panel, there is a 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together.

    It also features a Bluetooth receiver and pair button with a handy LED indicator to check if its in pairing mode or already connected to a device. Bluetooth pair name can be customized as desired. The Bluetooth receiver works with iPhones, iPads, iOS & Android smartphones, tablets, PC, Laptops, Desktops, etc…

    The WP225 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with glass, it will blend into any environment.

    125,00 
  • Toode lisati ostukorvi:

    Audac MBS104R Paigalduskomplekt nelja AUDAC S-Box™ mooduli paigaldamiseks 19" racki

    MBS104R-Small
    MBS104R-Small
    0 out of 5

    Audac MBS104R Paigalduskomplekt nelja AUDAC S-Box™ mooduli paigaldamiseks 19″ racki

    The MBS1xx is a series of installation accessories for use in combination with the AUDAC S-Box™ products range. This range includes a variation of small electronic products such as amplifiers, transformer boxes, converters, and many more.

    In combination with the MBS1xx series, extended assembly possibilities are offered to allow them to be fixed underneath tables or desks, assembled above drop ceilings or mounted to 19” equipment racks. The mechanic construction for each of these products is identical, allowing a combined installation for various products.

    23,42 
  • Toode lisati ostukorvi:

    Power amplifier kit

    Kohatäide
    0 out of 5

    Power amplifier kit

    The POW2 is an optional power amplifier kit which can be installed inside the R2 and M2 Multi-Zone Digital Audio Matrix housing. In its standard configuration, the R2 or M2 is equipped with 8 line level output channels on which the appropriate amplifiers can be connected, depending on the required power for the specific application. For certain applications where no large power capacities are required, the optional power amplifier kit can be installed, resulting in a multifunctional matrix and power amplifier merged into one single housing. The POW2 consists of a 16 channel (8 Stereo channel) Class-D amplifier, delivering a power of 60 Watt to every channel at 4 Ohm. In bridge mode, an output power of 8 x 120 Watt can be obtained at 8 Ohm. It features an advanced protection circuit which protects against DC malfunctioning, short circuit, overheating and overload while a large heatsink and speed controlled ventilation fan ensure a proper operation temperature is continuously maintained. The POW2 power amplifier kit includes the power amplifier module, a switching power supply and all necessary connection and installation accessories to properly install the kit inside the R2 or M2’s housing. Note: The POW2 replaces the older R2POW model, which offered comparable functionality and performance.

    832,50 
  • Toode lisati ostukorvi:

    Audac PC3000/W Programmivalija 45 x 45 mm, valge

    Kohatäide
    0 out of 5

    Audac PC3000/W Programmivalija 45 x 45 mm, valge

    The PC3000 is a flush mount wall program selector for 100V PA installations. It is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm installation materials. The output can be selected out of 5 different sources using the rotatable dial. Due to it’s slim and good looking design, these program selectors will blend into all kinds of different environments or interiors. The construction of the PC3000 is made with sturdy ABS and therefore suitable for big projects in industrial buildings to the standard installation into home design interiors. The connections are made at the rear side, using screw terminal blocks. Matching coverplates for the PC3000 are separately available (CP45CF). Available in Black (/B) and White (/W).

    30,92 
  • Toode lisati ostukorvi:

    Audac RMT40 Distantsjuhtimispult universaalne

    Kohatäide
    0 out of 5

    Audac RMT40 Distantsjuhtimispult universaalne

    The RMT40 remote controller can be used in combination with a variety of audio source devices. It features 13 buttons with various functions depending on the unit it is connected to.

    2.4 GHz wireless technology offers a transmission distance up to ~ 10 meters, allowing out-of-sight operation which is a great advantage compared to regular IR remote control systems. An included USB type receiver shall be connected to the provided USB slot on the audio source device. Transmitters and receivers are matched with unique ID’s, allowing simultaneous operation of multiple systems without disturbance while receiver extension is possible using USB extension cables when installed in closed/shielded cabinets.

    It is constructed of high-quality ABS materials with a brushed look finishing, giving it stylish elegant appearance while rubber-type buttons offer a comfortable feel. The transmitter is powered by 2 x AAA (included) batteries.

    Discover more about our modular audio players

    19,75 
  • Toode lisati ostukorvi:

    Audac MBS101R Paigalduskomplekt ühe AUDAC S-Box™ mooduli paigaldamiseks 19" racki

    MBS101R-Small
    MBS101R-Small
    0 out of 5

    Audac MBS101R Paigalduskomplekt ühe AUDAC S-Box™ mooduli paigaldamiseks 19″ racki

    The MBS1xx is a series of installation accessories for use in combination with the AUDAC S-Box™ products range. This range includes a variation of small electronic products such as amplifiers, transformer boxes, converters, and many more.

    In combination with the MBS1xx series, extended assembly possibilities are offered to allow them to be fixed underneath tables or desks, assembled above drop ceilings or mounted to 19” equipment racks. The mechanic construction for each of these products is identical, allowing a combined installation for various products.

    14,83 
  • Toode lisati ostukorvi:

    Audac TR2050 Eraldustrafo 2x RCA-M - 3,5mm pulk

    Kohatäide
    0 out of 5

    Audac TR2050 Eraldustrafo 2x RCA-M – 3,5mm pulk

    The TR2060 is a basic ground loop isolator, designed to electrically isolate audio devices from each other. Hum in audio systems is usually caused by ground loops in the system. A common mode current will flow in a ground loop created by an electrical system that has grounds on different voltage potentials. This results in a 50 Hz hum in the audio signal. The most common method to solve these problems is an audio isolation transformer such as the TR2060 which always need to be in reach for every audio technician. When ground loop problems are encountered, these can be solved in a jiffy, by using the TR2060.

    8,92 
  • Toode lisati ostukorvi:

    Audac WP210/B Sisendpaneel universaalne, valge

    Kohatäide
    0 out of 5

    Audac WP210/B Sisendpaneel universaalne, valge

    The WP210 is a remote wall mixer that can be used in combination with various AUDAC hardware (ARES5A, MTX series, AMP523 and more). It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, … ) or balanced microphone to the level corresponding to the differential signal input making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling. On the front side of the wall panel, there is a 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together.

    The WP210 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with glass, it will blend into any environment

    87,50 
  • Toode lisati ostukorvi:

    Audac VC3036/B Helitugevuse regulaator releega 100V/36W 45x45mm, must

    Kohatäide
    0 out of 5

    Audac VC3036/B Helitugevuse regulaator releega 100V/36W 45x45mm, must

    The VC3036 is a flush mount wall volume controllers for 100V PA installations. It is compatible with AUDAC and Niko installation materials. The volume is adjustable with a rotatable dial in ten steps of 3 dB and the maximum power rating is 36 Watt. A built-in relay makes it possible to build priority circuits between several controllers. Available in Black (B) and White (W). The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

    50,17 
  • Toode lisati ostukorvi:

    Audac WP210/B Sisendpaneel universaalne, must

    Kohatäide
    0 out of 5

    Audac WP210/B Sisendpaneel universaalne, must

    The WP210 is a remote wall mixer that can be used in combination with various AUDAC hardware (ARES5A, MTX series, AMP523 and more). It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, … ) or balanced microphone to the level corresponding to the differential signal input making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling. On the front side of the wall panel, there is a 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together.

    The WP210 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with glass, it will blend into any environment

    87,50 
  • Toode lisati ostukorvi:

    Audac WB3102/SW Paigalustoos pinnapealne VC3xx2 helitugevuse regulaatorile

    Kohatäide
    0 out of 5

    Audac WB3102/SW Paigalustoos pinnapealne VC3xx2 helitugevuse regulaatorile

    The WB3102 are wall mounting boxes for the VC3xx2-series volume controllers. The surface mount version is available in white colour (/SW).

    9,67 
  • Toode lisati ostukorvi:

    Audac TR106 Eraldustrafo 1:1/600Ω

    Kohatäide
    0 out of 5

    Audac TR106 Eraldustrafo 1:1/600Ω

    The AUDAC TR106 is a shielded true isolation audio transformer. Hum in audio systems is usually caused by ground loops in the system. A common mode current will flow in a ground loop created by an electrical system that has grounds on different voltage potentials. This results in a 50 Hz hum in the audio signal. The most common method to solve these problems is an audio transformer. The AUDAC TR106 audio isolation transformer with an in- and output impedance of 600 Ohm and a turns ratio of 1 : 1 has a very wide bandwidth and very low distortion which ensures a non distorted bass response and non attenuated high frequencies.

    25,92 
  • Toode lisati ostukorvi:

    Audac MWX45/W Juhtpaneel MTX maatriksile, 45x45mm, valge

    MWX43-45-W-Small
    MWX43-45-W-Small
    0 out of 5

    Audac MWX45/W Juhtpaneel MTX maatriksile, 45x45mm, valge

    The MWX45 are wall panel controllers to be used in combination with the AUDAC MTX series multi-zone audio matrix systems and the AUDAC AMP523MK2 & RM523. It provides the possibility to select the desired audio source and control the volume for one zone. The 7 segment LED display indicates the current selected audio source (1-8) or volume. The connection between the wall panel and the matrix system is achieved by using standard CAT5 UTP cable which should be connected to the terminal block connector on the back side of the wall panel. The wall panels are available in 45 mm, this version is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm installation materials. Thanks to its slim and good looking design, these wall panel controllers will blend into all kinds of different environments or interiors. Available in black (/B) and white (/W). There are two different AUDAC cover frames with metal subframe available, for 1 or 2 units, which are also available in black (/B) or white (/W).

    54,08 
  • Toode lisati ostukorvi:

    Audac DSC100/B Kõlarikaabel trossiga 10m, must

    DSC-B-Small
    DSC-B-Small
    0 out of 5

    Audac DSC100/B Kõlarikaabel trossiga 10m, must

    Connection cable with dual steel core, snap hook & open ends – 10 meter. For use with the ALTI series speakers (not suited for ALTIxM series). This connection cable with two integrated steel cores is designed for suspension with an additional drop safety. Fixation is made through two snap-hooks on one end and a dual Gripple™ fixation on the other end.

    42,00 
  • Toode lisati ostukorvi:

    Audac WB5065/W Paigalustoos pinnapealne DW5065/WP523/MWX65 paneelidele, valge

    Kohatäide
    0 out of 5

    Audac WB5065/W Paigalustoos pinnapealne DW5065/WP523/MWX65 paneelidele, valge

    The WB5065are surface mountwall boxes for AUDAC wall control panels such as the DW5066, MWX65 and WP523. Surface mounting boxes are available in white (WB5065/SW) and black (WB5065/SB).

    10,00 
  • Toode lisati ostukorvi:

    Audac PC3000/B Programmivalija 45 x 45 mm, must

    Kohatäide
    0 out of 5

    Audac PC3000/B Programmivalija 45 x 45 mm, must

    The PC3000 is a flush mount wall program selector for 100V PA installations. It is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm installation materials. The output can be selected out of 5 different sources using the rotatable dial. Due to it’s slim and good looking design, these program selectors will blend into all kinds of different environments or interiors. The construction of the PC3000 is made with sturdy ABS and therefore suitable for big projects in industrial buildings to the standard installation into home design interiors. The connections are made at the rear side, using screw terminal blocks. Matching coverplates for the PC3000 are separately available (CP45CF). Available in Black (/B) and White (/W).

    30,92 
  • Toode lisati ostukorvi:

    Audac WP225/W Sisendpaneel universaalne Bluetooth-ga, valge

    Kohatäide
    0 out of 5

    Audac WP225/W Sisendpaneel universaalne Bluetooth-ga, valge

    The WP225 is a remote wall mixer that can be used in combination with various AUDAC hardware (ARES5A, MTX series, AMP523 and more). It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, … ) or balanced microphone to the level corresponding to the differential signal input making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling. On the front side of the wall panel, there is a 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together.

    It also features a Bluetooth receiver and pair button with a handy LED indicator to check if its in pairing mode or already connected to a device. Bluetooth pair name can be customized as desired. The Bluetooth receiver works with iPhones, iPads, iOS & Android smartphones, tablets, PC, Laptops, Desktops, etc…

    The WP225 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with glass, it will blend into any environment.

    125,00 
  • Toode lisati ostukorvi:

    Audac WMI18/W Pesapaneel 45x45mm XLR-F - EB-4p konverter, valge

    Kohatäide
    0 out of 5

    Audac WMI18/W Pesapaneel 45x45mm XLR-F – EB-4p konverter, valge

    The WMI are flush mountable Wall Microphone Input Units, which can be integrated into several kinds of installation materials for system integration. They are fitted with a Female XLR input connector on the front side and a terminal block connector on the rear side. The signal which is applied to the input connection is converted to a differential signal with increased voltage levels. This way, the signal is made insensitive to interference and noise and can be transferred over a long distance without any loss of quality. This allows reliable signal transmission up to 300 meters over CAT5E (or better) twisted pair cabling. A jumper on the rear side allows enabling of 15 Volts phantom power. It should be used in combination with a matching device on the receiver end.

    62,42 
  • Toode lisati ostukorvi:

    Audac MWX45/B Juhtpaneel MTX maatriksile, 45x45mm, must

    MWX43-45-B-Small
    MWX43-45-B-Small
    0 out of 5

    Audac MWX45/B Juhtpaneel MTX maatriksile, 45x45mm, must

    The MWX45 are wall panel controllers to be used in combination with the AUDAC MTX series multi-zone audio matrix systems and the AUDAC AMP523MK2 & RM523. It provides the possibility to select the desired audio source and control the volume for one zone. The 7 segment LED display indicates the current selected audio source (1-8) or volume. The connection between the wall panel and the matrix system is achieved by using standard CAT5 UTP cable which should be connected to the terminal block connector on the back side of the wall panel. The wall panels are available in 45 mm, this version is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm installation materials. Thanks to its slim and good looking design, these wall panel controllers will blend into all kinds of different environments or interiors. Available in black (/B) and white (/W). There are two different AUDAC cover frames with metal subframe available, for 1 or 2 units, which are also available in black (/B) or white (/W).

    54,08 
  • Toode lisati ostukorvi:

    Audac TR2050 Eraldustrafo 3,5mm pistik - 3,5mm pesa

    Kohatäide
    0 out of 5

    Audac TR2050 Eraldustrafo 3,5mm pistik – 3,5mm pesa

    The TR2070 is a basic ground loop isolator, designed to electrically isolate audio devices from each other. Hum in audio systems is usually caused by ground loops in the system. A common mode current will flow in a ground loop created by an electrical system that has grounds on different voltage potentials. This results in a 50 Hz hum in the audio signal. The most common method to solve these problems is an audio isolation transformer such as the TR2070 which always need to be in reach for every audio technician. When ground loop problems are encountered, these can be solved in a jiffy, by using the TR2070.

    8,92 
  • Toode lisati ostukorvi:

    Audac VC3060/W Helitugevuse regulaator releega 100V/60W 45x45mm, valge

    Kohatäide
    0 out of 5

    Audac VC3060/W Helitugevuse regulaator releega 100V/60W 45x45mm, valge

    The VC3062 controllers are 100 Volt wall volume controllers whereby the volume for 100 V loudspeakers can be adjusted in 11 steps of 3 dB. They feature a slim and good looking design and are constructed out of sturdy ABS, making them suitable for big projects in industrial environments as well as standard home interiors. An integrated 24 Volt relay allows bypassing of the volume controller in priority situations, making sure the message is always clearly heard at maximum volume. Connections are made using screw terminal blocks, and flush and surface mount boxes (WB3102) are separately available.

    31,42 
  • Toode lisati ostukorvi:

    Audac VC3208/W Helitugevuse regulaator pingega juhitavale võimendile, 45x45mm, valge

    Kohatäide
    0 out of 5

    Audac VC3208/W Helitugevuse regulaator pingega juhitavale võimendile, 45x45mm, valge

    The VC3208 is a flush mount wall controller for volume regulation of voltage controlled amplifiers such as the AMP20MK2. The volume is fluently controllable using the rotatable dial with potentiometer. The connection between the amplifier and the regulator is made using twisted pair CAT5e (or better) cabling fitted with a pluggable terminal block connector. The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

    21,83 
  • Toode lisati ostukorvi:

    Audac WP523/B Sisendpaneel LX523 kõlarile, must

    Kohatäide
    0 out of 5

    Audac WP523/B Sisendpaneel LX523 kõlarile, must

    The WP523 is a remote wall mixer which is meant to be used in combination with the LX523 active speaker system. It converts the signal coming from a stereo line-level audio source (such as CD-player, tuner, MP3 player, … ) or balanced microphone to the level corresponding the differential signal input on the LX523 (RJ45) making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted pair CAT5 cabling. On the front side of the wall panel, there is a stereo RCA line input available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together. A main volume dial allows you to adjust the overall volume of the loudspeaker system. The mixing potentiometers are level with the surface and both equipped with a Push-Lock mechanism. They can be opened and hidden again by pressing it. An internal limiter avoids distortion on the input signal and intervenes when the level of the input signal reaches the clipping level. The ‘Clip’ LED located above the mixing potentiometer will illuminate when it’s recommended to reduce the level. This should be done by turning back the potentiometer. A jumper on the rear side of the panel allows you to enable the 12V phantom power for the microphone input. The connection of the wall panel should be done with twisted pair UTP CAT5 cabling whereby distances up to 500 meters can be reached. It should be connected to the 8-pin Euro-Terminal Block connector on the rear side of the panel. Available in black (/B) and white (/W).

    51,33 
  • Toode lisati ostukorvi:

    Audac MBS310 Paigalduskomplekt ½ 1U mooduli paigaldamiseks 19" racki

    MBS310-1-Small
    MBS310-1-SmallMBS310-3-Small
    0 out of 5

    Audac MBS310 Paigalduskomplekt ½ 1U mooduli paigaldamiseks 19″ racki

    The MBS310 rack mounting set is designed to safely and effectively mount half rackspace devices into 19” or 10.5” racks. 

    The flowing configurations are possible with this set: 

    • One half rackspace device in to a 19” rack (1 HE)
    • Two half rackspace devices in to a 19” rack (1 HE)
    • One half rackspace device in to a 10.5” rack (1 HE)
       

    The set contains: 

    • 1 x single mounting ear 
    • 2 x double mounting ears 
    • 2 x couplers 
    • 8 x screws M4 x 6mm
    22,83 
  • Toode lisati ostukorvi:

    Audac WP205/B Kõlari ARES5A sisendpaneel, must

    Kohatäide
    0 out of 5

    Audac WP205/B Kõlari ARES5A sisendpaneel, must

    The WP205 is a remote wall mixer that is meant to be used in combination with the ARES5A active speaker system. It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, … ) or balanced microphone to the level corresponding to the differential signal input on the ARES5A (RJ45) making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling. On the front side of the wall panel, there is a 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together.

    The WP205 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with Acrylic (PMMA) glass finish, it will blend into any environment.

    55,83 
  • Toode lisati ostukorvi:

    Audac MBS103R Paigalduskomplekt kolme AUDAC S-Box™ mooduli paigaldamiseks 19" racki

    MBS103R-Small
    MBS103R-Small
    0 out of 5

    Audac MBS103R Paigalduskomplekt kolme AUDAC S-Box™ mooduli paigaldamiseks 19″ racki

    The MBS1xx is a series of installation accessories for use in combination with the AUDAC S-Box™ products range. This range includes a variation of small electronic products such as amplifiers, transformer boxes, converters, and many more.

    In combination with the MBS1xx series, extended assembly possibilities are offered to allow them to be fixed underneath tables or desks, assembled above drop ceilings or mounted to 19” equipment racks. The mechanic construction for each of these products is identical, allowing a combined installation for various products.

    21,25 
  • Toode lisati ostukorvi:

    Audac VC3208/B Helitugevuse regulaator pingega juhitavale võimendile, 45x45mm, must

    Kohatäide
    0 out of 5

    Audac VC3208/B Helitugevuse regulaator pingega juhitavale võimendile, 45x45mm, must

    The VC3208 is a flush mount wall controller for volume regulation of voltage controlled amplifiers such as the AMP20MK2. The volume is fluently controllable using the rotatable dial with potentiometer. The connection between the amplifier and the regulator is made using twisted pair CAT5e (or better) cabling fitted with a pluggable terminal block connector. The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

    21,83 
  • Toode lisati ostukorvi:

    Audac MWX65/B Juht- ja sisendpaneel MTX maatriksile, must

    MWX65-B-Small
    MWX65-B-Small
    0 out of 5

    Audac MWX65/B Juht- ja sisendpaneel MTX maatriksile, must

    The MWX65 is an all-in-one wall panel controller to be used in combination with the AUDAC MTX series multi-zone audio matrix systems. It can control the input signal and volume for one zone and also contains an additional line and microphone level input which can be patched to the zone it is connected to. Both input selection and volume control as well as two band tone control can be controlled using the versatile rotatable push-dial while the integrated 2.5” graphical display ensures a user friendly experience. An XLR connector is provided as additional microphone input while the line input is performed using RCA connectors. The signals applied to these inputs can be used as one additional local input. This enables you to connect any CD or MP3 player as local music source or connect a microphone for speeches or other announcements. The input mixing can be done by using both push-lock potentiometers. The microphone input has the possibility to provide 12V phantom power which can be turned on and off by software configuration. The wiring between the matrix and the wall panel should be performed by using standard UTP CAT5 cabling which transfers both the control and audio signals to the matrix while providing the power supply for the wall panel.

    158,92 
  • Toode lisati ostukorvi:

    Audac WB3102/FG Paigaldustoos kipsseina VC3xx2 helitugevuse regulaatorile

    Kohatäide
    0 out of 5

    Audac WB3102/FG Paigaldustoos kipsseina VC3xx2 helitugevuse regulaatorile

    The WB3102 are wall mounting boxes for the VC3xx2-series volume controllers. The flush mount version allows installation in hollow walls (/FG).

    4,92 
  • Toode lisati ostukorvi:

    Audac RGA12 DAB/DAB+ välisantenn

    Kohatäide
    0 out of 5

    Audac RGA12 DAB/DAB+ välisantenn

    DAB signal is superior for those who have imperfect signal or a low quality system. The RGA12 antenna is optimized for best DAB+ signal reception. The construction allows antenna assembly around any pole with a 30~50 mm diameter, while the aluminum construction is resistant for permanent outdoor exposure to the elements. Connections are made using an included F-type connector.

    40,67 
  • Toode lisati ostukorvi:

    Audac WLI18/B Pesapaneel 2x RCA, 45x45mm, must

    Kohatäide
    0 out of 5

    Audac WLI18/B Pesapaneel 2x RCA, 45x45mm, must

    The WLI are flush mountable Wall Line Input Units, which can be integrated into several kinds of installation materials for system integration. They are fitted with two RCA connectors (stereo) on the front side and a terminal block connector on the rear side. The signal which is applied to the input connections is converted to a differential dual mono signal with increased voltage levels. This way, the signal is made insensitive to interference and noise and can be transferred over a long distance without any loss of quality. This allows reliable signal transmission up to 300 meters over CAT5E (or better) twisted pair cabling. It should be used in combination with a matching device on the receiver end.

    63,00 
  • Toode lisati ostukorvi:

    Audac MBS101T Paigalduskomplekt ühe AUDAC S-Box™ mooduli kinnitamiseks tasapinnale

    MBS101T-Small
    MBS101T-Small
    0 out of 5

    Audac MBS101T Paigalduskomplekt ühe AUDAC S-Box™ mooduli kinnitamiseks tasapinnale

    The MBS1xx is a series of installation accessories for use in combination with the AUDAC S-Box™ products range. This range includes a variation of small electronic products such as amplifiers, transformer boxes, converters, and many more.

    In combination with the MBS1xx series, extended assembly possibilities are offered to allow them to be fixed underneath tables or desks, assembled above drop ceilings or mounted to 19” equipment racks. The mechanic construction for each of these products is identical, allowing a combined installation for various products.

    5,25 
  • Toode lisati ostukorvi:

    Audac M2DIS 7” puuteekraan M2-le

    M2DIS-Small
    M2DIS-Small
    0 out of 5

    Audac M2DIS 7” puuteekraan M2-le

    The M2DIS is an optional display unit with touchscreen which can be installed internally in the front panel of the M2 Multi-Media Digital Audio Mixer. This unit consists of a 7” TFT display panel with a resolution of 800 x 480 px that is fitted with a resistive touch-screen panel. It is controlled by a powerful 32 bit processor which communicates directly with the M2’s DSP processor. This unit allows the user to operate the control functions of the matrix systems without any external equipment. So it is now possible to set up zone selection or input mixing without any external devices. This can be useful when the system is installed in a technical room where no external control devices are within reach.

    625,00 
  • Toode lisati ostukorvi:

    Audac CP45ARP/B Pesapaneel repiiteriga RJ45, 45x45mm, must

    CP45ARP-Small
    CP45ARP-Small
    0 out of 5

    Audac CP45ARP/B Pesapaneel repiiteriga RJ45, 45x45mm, must

    The CP45ARP allows you to attach one APM paging console on the front, while the phoenix connector on the back lets you route the signal to a next paging console or junction box. It can offer 20V power to the APM console and is also equipped with 2 jumpers to terminate the audio -or databus. An advantage the ARP version has over the ARJ version is that it also offers a built-in repeater. This repeater extends the maximum distance from 300m to 600m. The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

    45,92 
  • Toode lisati ostukorvi:

    Audac ARJ03P Ühenduspaneel süsteemne

    ARJ03P-shadow-Small
    ARJ03P-shadow-Small
    0 out of 5

    Audac ARJ03P Ühenduspaneel süsteemne

    Universaalne RJ45 splitter/liitmik süsteemne
    Paigaldus DIN latile
    Lisa toiteallika võimalus liinile

    33,33 
  • Toode lisati ostukorvi:

    Audac CP45ARPJ/W Pesapaneel repiiteriga RJ45, 45x45mm, valge

    CP45ARP-Small-2
    CP45ARP-Small-2
    0 out of 5

    Audac CP45ARPJ/W Pesapaneel repiiteriga RJ45, 45x45mm, valge

    The CP45ARP allows you to attach one APM paging console on the front, while the phoenix connector on the back lets you route the signal to a next paging console or junction box. It can offer 20V power to the APM console and is also equipped with 2 jumpers to terminate the audio -or databus. An advantage the ARP version has over the ARJ version is that it also offers a built-in repeater. This repeater extends the maximum distance from 300m to 600m. The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

    46,58 
  • Toode lisati ostukorvi:

    Audac WP205/W Kõlari ARES5A sisendpaneel, valge

    Kohatäide
    0 out of 5

    Audac WP205/W Kõlari ARES5A sisendpaneel, valge

    The WP205 is a remote wall mixer that is meant to be used in combination with the ARES5A active speaker system. It converts the signal coming from a stereo line-level audio source (such as a tuner, mobile devices, … ) or balanced microphone to the level corresponding to the differential signal input on the ARES5A (RJ45) making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling. On the front side of the wall panel, there is a 3.5 mm jack stereo line input connection available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together.

    The WP205 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with Acrylic (PMMA) glass finish, it will blend into any environment.

    55,83 
  • Toode lisati ostukorvi:

    Audac WP523/W Sisendpaneel LX523 kõlarile, valge

    Kohatäide
    0 out of 5

    Audac WP523/W Sisendpaneel LX523 kõlarile, valge

    The WP523 is a remote wall mixer which is meant to be used in combination with the LX523 active speaker system. It converts the signal coming from a stereo line-level audio source (such as CD-player, tuner, MP3 player, … ) or balanced microphone to the level corresponding the differential signal input on the LX523 (RJ45) making it possible to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted pair CAT5 cabling. On the front side of the wall panel, there is a stereo RCA line input available together with a balanced XLR microphone input, both provided with their own knob which allows the signals to be mixed together. A main volume dial allows you to adjust the overall volume of the loudspeaker system. The mixing potentiometers are level with the surface and both equipped with a Push-Lock mechanism. They can be opened and hidden again by pressing it. An internal limiter avoids distortion on the input signal and intervenes when the level of the input signal reaches the clipping level. The ‘Clip’ LED located above the mixing potentiometer will illuminate when it’s recommended to reduce the level. This should be done by turning back the potentiometer. A jumper on the rear side of the panel allows you to enable the 12V phantom power for the microphone input. The connection of the wall panel should be done with twisted pair UTP CAT5 cabling whereby distances up to 500 meters can be reached. It should be connected to the 8-pin Euro-Terminal Block connector on the rear side of the panel. Available in black (/B) and white (/W).

    51,33 
  • Toode lisati ostukorvi:

    Audac WP220/W Sisendpaneel Bluetooht ühenduseks, valge

    Kohatäide
    0 out of 5

    Audac WP220/W Sisendpaneel Bluetooht ühenduseks, valge

    The WP220 is a remote universal wall panel with Bluetooth receiver input that can be used in combination with various AUDAC hardware (ARES5A, MTX series, AMP523 and more). It was never easier connecting your Bluetooth enabled device with your audio installation using this wall plate.  It will enable you to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling.

    On the front side of the wall panel, you’ll find a Bluetooth pair button with a handy LED indicator to check if its in pairing mode or already connected to a device. Bluetooth pair name can be customized as desired. The Bluetooth receiver works with iPhones, iPads, iOS & Android smartphones, tablets, PC, Laptops, Desktops, etc…

    The WP220 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with glass, it will blend into any environment.

    108,33 
  • Toode lisati ostukorvi:

    Audac VC3022/W Helitugevuse regulaator releega 100V/20W 80x80mm, valge

    Kohatäide
    0 out of 5

    Audac VC3022/W Helitugevuse regulaator releega 100V/20W 80x80mm, valge

    The VC3xx2 Series are 100 Volt wall volume controllers whereby the volume for 100 V loudspeakers can be adjusted in 11 steps of 3 dB. They feature a slim and good looking design and are constructed out of sturdy ABS, making them suitable for big projects in industrial environments as well as standard home interiors. An integrated 24 Volt relay allows bypassing of the volume controller in priority situations, making sure the message is always clearly heard at maximum volume. Connections are made using screw terminal blocks, and flush and surface mount boxes (WB3102) are separately available.

    16,83 
  • Toode lisati ostukorvi:

    Audac CPE100 Käepidemed CAP ja CPA võimenditele

    CPE100-Small
    CPE100-Small
    0 out of 5

    Audac CPE100 Käepidemed CAP ja CPA võimenditele

    These screwable brackets can be attached to the front of a CPA/CPR unit and allows you to remove the unit from the rack in which it is installed more easily.

    6,58 
  • Toode lisati ostukorvi:

    Audac RGA10 FM välisantenn

    Kohatäide
    0 out of 5

    Audac RGA10 FM välisantenn

    The RGA10 is an omnidirectional outdoor antenna for FM radio reception. The circular construction allows antenna assembly around any pole with a 30~50 mm diameter, while the aluminum construction is resistant for permanent outdoor exposure to the elements. Connections are made using an included F-type connector.

    33,33 
  • Toode lisati ostukorvi:

    Audac MBS102R Paigalduskomplekt kahe AUDAC S-Box™ mooduli paigaldamiseks 19" racki

    MBS102R-Small
    MBS102R-Small
    0 out of 5

    Audac MBS102R Paigalduskomplekt kahe AUDAC S-Box™ mooduli paigaldamiseks 19″ racki

    The MBS1xx is a series of installation accessories for use in combination with the AUDAC S-Box™ products range. This range includes a variation of small electronic products such as amplifiers, transformer boxes, converters, and many more.

    In combination with the MBS1xx series, extended assembly possibilities are offered to allow them to be fixed underneath tables or desks, assembled above drop ceilings or mounted to 19” equipment racks. The mechanic construction for each of these products is identical, allowing a combined installation for various products.

    18,42 
  • Toode lisati ostukorvi:

    Audac WLI18/W Pesapaneel 2x RCA, 45x45mm, valge

    Kohatäide
    0 out of 5

    Audac WLI18/W Pesapaneel 2x RCA, 45x45mm, valge

    The WLI are flush mountable Wall Line Input Units, which can be integrated into several kinds of installation materials for system integration. They are fitted with two RCA connectors (stereo) on the front side and a terminal block connector on the rear side. The signal which is applied to the input connections is converted to a differential dual mono signal with increased voltage levels. This way, the signal is made insensitive to interference and noise and can be transferred over a long distance without any loss of quality. This allows reliable signal transmission up to 300 meters over CAT5E (or better) twisted pair cabling. It should be used in combination with a matching device on the receiver end.

    63,00 
  • Toode lisati ostukorvi:

    Audac DSC100/W Kõlarikaabel trossiga 10m, valge

    DSC-W-Small
    DSC-W-Small
    0 out of 5

    Audac DSC100/W Kõlarikaabel trossiga 10m, valge

    Connection cable with dual steel core, snap hook & open ends – 10 meter. For use with the ALTI series speakers (not suited for ALTIxM series). This connection cable with two integrated steel cores is designed for suspension with an additional drop safety. Fixation is made through two snap-hooks on one end and a dual Gripple™ fixation on the other end.

    42,00 
  • Toode lisati ostukorvi:

    Audac WB3102/FS Paigalustoos kiviseina VC3xx2 helitugevuse regulaatorile

    Kohatäide
    0 out of 5

    Audac WB3102/FS Paigalustoos kiviseina VC3xx2 helitugevuse regulaatorile

    The WB3102 are wall mounting boxes for the VC3xx2-series volume controllers. The flush mount version allows installation in brick or concrete walls (/FS).

    4,92 
  • Toode lisati ostukorvi:

    Audac ATU44MK2 Sisendadapter universaalne

    ATU44-MK2-Small
    ATU44-MK2-Small
    0 out of 5

    Audac ATU44MK2 Sisendadapter universaalne

    Universaalne sisendi konverter

    68,00 
  • Toode lisati ostukorvi:

    Audac WB50/FG Paigalustoos kipsseina DW5065/WP523/MWX65 paneelidele

    Kohatäide
    0 out of 5

    Audac WB50/FG Paigalustoos kipsseina DW5065/WP523/MWX65 paneelidele

    The WB50 are wall boxes for mounting AUDAC wall control panels such as the DW5066, MWX65 and WP523. The /FG is the white plastic version that is meant for flush mounting in Gypsum walls.

    6,75 
  • Toode lisati ostukorvi:

    Audac CP45PE/B Pesapaneel Speacon kõlaripesa, 45x45mm, must

    CP45SPEB-Small
    CP45SPEB-Small
    0 out of 5

    Audac CP45PE/B Pesapaneel Speacon kõlaripesa, 45x45mm, must

    Connection plate with Neutrik Speakon connector, designed to be used with AUDAC, Niko or standard 45 x 45 installation materials. Available in Black (/B) & White (/W). (Mounting frame and cover plate not included)

    6,42 
  • Toode lisati ostukorvi:

    Audac VC3036/W Helitugevuse regulaator releega 100V/36W 45x45mm, valge

    Kohatäide
    0 out of 5

    Audac VC3036/W Helitugevuse regulaator releega 100V/36W 45x45mm, valge

    The VC3036 is a flush mount wall volume controllers for 100V PA installations. It is compatible with AUDAC and Niko installation materials. The volume is adjustable with a rotatable dial in ten steps of 3 dB and the maximum power rating is 36 Watt. A built-in relay makes it possible to build priority circuits between several controllers. Available in Black (B) and White (W). The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

    50,17 
  • Toode lisati ostukorvi:

    Audac OPT2 Optiliste sisendite moodul M2 meediamaatriksile

    Kohatäide
    0 out of 5

    Audac OPT2 Optiliste sisendite moodul M2 meediamaatriksile

    The OPT2 is a fiber interconnection interface for the R2 and M2 Digital Multi-Zone & Multi-Media Matrix Systems. This module makes it possible to transfer up to 16 digital audio signals over one single fiber conductor (8 stereo channels) for covering large distances.A duplex 62.5 / 125 µm multimode glass fiber terminated with ST/PC connectors should be used for linking the devices with each other.The wiring of the entire system needs to be done according to a closed loop principle where the output is connected to the input of the next device in the chain and the last device gives feedback to the input of the first device.Multiple devices (up to 15 pcs) can be cascaded through series linking with a maximum distance of 1000 meters between two devices. The especially developed protocol for this purpose guarantees an accurate signal transmission with maximal speed and reliability. The OPT2 includes all software and accessories (except the fiber) which are necessary to control and configure the system. The selection of the signals to be transferred and the zone assignment can be made in the user interface of the system.Recommended fiber to be used in combination with OPT2 is ‘PROCAB FBS125 Duplex Fiber Optic ST/PC to ST/PC 62.5/125µm’. This optic transmitter is compatible with 50/125 μm, 62.5/125 μm, 100/140 μm, and 200 μm HCS® Fiber.

    370,83 
  • Toode lisati ostukorvi:

    Audac WMI18/B Pesapaneel 45x45mm XLR-F - EB-4p konverter, must

    Kohatäide
    0 out of 5

    Audac WMI18/B Pesapaneel 45x45mm XLR-F – EB-4p konverter, must

    The WMI are flush mountable Wall Microphone Input Units, which can be integrated into several kinds of installation materials for system integration. They are fitted with a Female XLR input connector on the front side and a terminal block connector on the rear side. The signal which is applied to the input connection is converted to a differential signal with increased voltage levels. This way, the signal is made insensitive to interference and noise and can be transferred over a long distance without any loss of quality. This allows reliable signal transmission up to 300 meters over CAT5E (or better) twisted pair cabling. A jumper on the rear side allows enabling of 15 Volts phantom power. It should be used in combination with a matching device on the receiver end.

    62,42 
  • Toode lisati ostukorvi:

    Audac DSC70/W Kõlarikaabel trossiga 7m, valge

    DSC-W-Small-2
    DSC-W-Small-2
    0 out of 5

    Audac DSC70/W Kõlarikaabel trossiga 7m, valge

    Connection cable with dual steel core, snap hook & open ends – 7 meter. For use with the ALTI series speakers (not suited for ALTIxM series). This connection cable with two integrated steel cores is designed for suspension with an additional drop safety. Fixation is made through two snap-hooks on one end and a dual Gripple™ fixation on the other end.

    33,83 
  • Toode lisati ostukorvi:

    Audac WP220/B Sisendpaneel Bluetooht ühenduseks, must

    Kohatäide
    0 out of 5

    Audac WP220/B Sisendpaneel Bluetooht ühenduseks, must

    The WP220 is a remote universal wall panel with Bluetooth receiver input that can be used in combination with various AUDAC hardware (ARES5A, MTX series, AMP523 and more). It was never easier connecting your Bluetooth enabled device with your audio installation using this wall plate.  It will enable you to transfer high-quality audio over long distances between the wall panel and the loudspeaker, by just using inexpensive twisted-pair CAT5e or better cabling.

    On the front side of the wall panel, you’ll find a Bluetooth pair button with a handy LED indicator to check if its in pairing mode or already connected to a device. Bluetooth pair name can be customized as desired. The Bluetooth receiver works with iPhones, iPads, iOS & Android smartphones, tablets, PC, Laptops, Desktops, etc…

    The WP220 is available in 2 colours (White – RAL9003 & Black – RAL9005) and is compatible with most standard EU (80×80 mm) style in-wall boxes for solid and hollow walls. With the Elegant ABS front panel with glass, it will blend into any environment.

    108,33 
  • Toode lisati ostukorvi:

    Audac ALI20MK2 Liini isolaator 2x

    ALI20MK2-Small
    ALI20MK2-Small
    0 out of 5

    Audac ALI20MK2 Liini isolaator 2x

    Stereo helisignaali eraldustrafo 1:1 600Ω.
    Sisend-väljund XLR pesadega.
    Maanduse eralduslüliti.

    102,00 
  • Toode lisati ostukorvi:

    Liinisplitter 1:3 IMG LSP-102

    Kohatäide
    0 out of 5

    Liinisplitter 1:3 IMG LSP-102

    65,83 
  • Toode lisati ostukorvi:

    Datavideo 2 Channel Audio 1:1 transformer

    DAC-80-output-nonsquare13042020115309
    DAC-80-output-nonsquare13042020115309DAC-80-input-nonsquare13042020115114
    0 out of 5

    Datavideo 2 Channel Audio 1:1 transformer

    2 Channel Audio 1:1 transformer

    115,00