26 Helindussüsteemi moodulid

The DW3020 is a flush mount wall panel controller designed to work in combination with the R2 amplifier. It can be installed in a separate zone, and gives the possibility to select the desired audio source and adjust the volume for the zone that it’s applied to. The connection between the amplifier and the controller is made by using standard UTP CAT5 cabling with RJ45 connectors.

All-in-one wall panel for MTX White version

Digital paging microphone 16 zones MK2 version

The CPA36 is a professional single channel 100V power amplifier with a power of 360 Watt, especially designed for most common 100V PA systems, and perfect to be used in combination with the CPR12 pre-amplifier. It is designed as a no-nonsense amplifier with only the necessary controls and connections. This creates great simplicity in use and installation. There are several power output taps available for use in 100V, 70V and even 4 Ohm Low impedance installations and they are fitted with an advanced multipurpose protection circuit. The protection circuit detects DC malfunction, short circuit, overheating, overload and limits the signal when necessary. Another present feature is the 24 V DC connection for powering the amplifier with emergency power when the main power is shut down. At the back of the amplifier, there are trim potentiometers to set the input level, a high pass filter switch and a ground lift switch provided. The input connection is made with balanced XLR connectors, and there’s a signal output for linking with other amplifiers. The steel 19″ housing has a height of 2 HE.

Active audio transceivers RCA MK2 version

Connection cable with dual steel core, snap hook & open ends – 10 meter Black

8-zone audio matrix

The DW3020 is a flush mount wall panel controller designed to work in combination with the R2 amplifier. It can be installed in a separate zone, and gives the possibility to select the desired audio source and adjust the volume for the zone that it’s applied to. The connection between the amplifier and the controller is made by using standard UTP CAT5 cabling with RJ45 connectors.

MTX wall panel controller 45 x 45 mm Black version

Wall panel controller 45 x 45 mm Black version

Setup box installation accessories Mounts three units into a 19” equipment rack (1 HE)

The CPA12 is a professional single channel 100V power amplifier with a power of 120 Watt, especially designed for most common 100V PA systems and perfect to be used in combination with the CPR12 pre-amplifier. It is designed as a no-nonsense amplifier with only the necessary controls and connections. This creates great simplicity in use and installation. There are several power output taps available for use in 100V, 70V and even 4 Ohm Low impedance installations and they are fitted with an advanced multipurpose protection circuit. The protection circuit detects DC malfunction, short circuit, overheating, overload and limits the signal when necessary. Another present feature is the 24 V DC connection for powering the amplifier with emergency power when the main power is shut down. At the back of the amplifier, there are trim potentiometers to set the input level, a high pass filter switch and a ground lift switch provided. The input connection is made with balanced XLR connectors and there is a signal output for linking with other amplifiers. The steel 19″ housing has a height of 2 HE.

The M2DIS is an optional display unit with touchscreen which can be installed internally in the front panel of the M2 Multi-Media Digital Audio Mixer. This unit consists of a 7” TFT display panel with a resolution of 800 x 480 px that is fitted with a resistive touch-screen panel. It is controlled by a powerful 32 bit processor which communicates directly with the M2’s DSP processor. This unit allows the user to operate the control functions of the matrix systems without any external equipment. So it is now possible to set up zone selection or input mixing without any external devices. This can be useful when the system is installed in a technical room where no external control devices are within reach.

The CP45ARP allows you to attach one APM paging console on the front, while the phoenix connector on the back lets you route the signal to a next paging console or junction box. It can offer 20V power to the APM console and is also equipped with 2 jumpers to terminate the audio -or databus. An advantage the ARP version has over the ARJ version is that it also offers a built-in repeater. This repeater extends the maximum distance from 300m to 600m. The 45 x 45 mm size is compatible with AUDAC, Niko, Legrand and other standard 45 x 45 mm Mounting frames and cover plates.

Quad-channel power amplifier 4 x 480W 100V

These screwable brackets can be attached to the front of a CPA/CPR unit and allows you to remove the unit from the rack in which it is installed more easily.

Connection cable with dual steel core, snap hook & open ends – 10 meter White